Showing posts with label lifepo4. Show all posts
Showing posts with label lifepo4. Show all posts

Monday, September 28, 2020

Building a new lithium battery

For years I have been using lithium batteries to power my radio equipment when portable, both LiPo and LiFePO4.
If you want to know more about these different types read this post I wrote a few years ago.

I started out buying batteries from HobbyKing in China. Then I decided to build a few myself with pouch cells I bought from AliExpress. 

Recently I lost two LiPo pouch cells when I abused a battery - forgetting to attach the under voltage alarm. Another LiPo cell of a different pack turned out dead without a clear cause. I ordered a new cell but they are quite expensive. Losing three of those cells in a short period of time I suspect I might have to replace more in the future. So I started looking for other solutions with cheaper building blocks: smaller cells.

LiPo cell after abuse

Looking at smaller cells I first stumbled upon the 18650. A popular Li-Ion battery and quite small but you need a lot of them to get a useful capacity as they are around 2Ah a piece. However I found more practical LiFePO4 cells with a 7Ah capacity: 32700. I bought a set of those with strips of nickel attached to the ends for soldering as I do not have a spot welder (yet).

The voltage of four of these LiFePO4 cells is too low for my amp - that is why I opted for LiPo up till now - but as the amp is designed to handle up to 18V a battery of 5 cells would do the job. So I decided to go for a 5s3p design (5 cells in series and 3 in parallel).

Building a 5s3p battery

I bought a BMS as well with the idea that it will protect the battery from under voltage. And it allows me to charge the battery even with a simple (non balancing) charger. I was hoping that a BMS is more effective in balancing than the chargers I have - that take quite some time to balance an unbalanced pack.

Completed battery with BMS

Testing the battery my first lesson was that you cannot charge a battery that has a BMS with a smart charger. The BMS starts kicking in when the first cell approaches its maximum. The charger notices the increasing resistance and shuts down with an error ("connection break"). 

Charging through the BMS with a smart charger 

Time for Plan B I used a 12V source and a step up converter to 18V to act as a "dumb" charger. Meanwhile I checked the charging current and the voltage of the individual cells to see what was happening. 

This time the charger patiently waited for the BMS to allow for a current to run. The BMS would drain the cells for a bit and then allow a charge current until one of the cells hit around 3.5V and then the cycle repeated. However it did not seem to be able to bring the cells closer together. After an hour there was still a spread of 0.2V between the cells. 

After letting the pack sit for a while I found out that the BMS aims to keep the cells at around 3.4V (on my V-meter). So during charging - aiming for 3.6V - a cell might go higher but the BMS will continue to discharge it until it is back at 3.4V again.

I will have to see if this noticeably impacts the capacity of this battery pack. When I have some more time on my hands I will run some tests and see how it behaves under the stress of powering a 400w amp.

Update May 2021:
After using the battery pack for a while I decided to remove the BMS. In my situation - having balancing chargers - the BMS only adds complexity.

The second thing I noticed is that the pack was struggling delivering the high amperage the ALS-500m pulls. Testing the pack at home with a dummy load I saw the nickel tabs I used to solder the main + and - wires to became hot, red hot even. 


So I decided to solder wires to the first and last set of (three) parallel batteries to spread the current. Testing that thoroughly I found it to work perfectly. All cells now discharge evenly, even under high load.

Shrink wrapped end result (with built-in Voltmeter)





Tuesday, May 24, 2016

Power sources for portable operation

When you start to go out on portable activities, you are confronted with the question what power source you should use. In this post I will share the choices I made working barefoot. 

The reason to share this info now is that I am in the middle of constructing something for my new mobile amplifier.. but more on that in a future post.

Introducing the challenge
The challenge depends on your operating conditions. Suppose that you are not going to work QRP and you will not be in or near your car. This is the situation I faced when I started activating special locations like nature reserves and castles.

Working with a 100W set, the power source you are looking for needs to supply you with approx 16A @13v, for as long as possible but with minimum weight. The good news is that there are a lot of other crazy hobbyists out there that face the same challenge. You will find them when you search for "RC" - remote controlled cars, planes, helicopters and more recently drones.

Working barefoot: LiPo and LiFePO4
These people have turned to LiPo (Lithium Polymer) and LiFePO4 (Lithium Iron Phosphate) batteries for their power.  LiPo and LiFePO4 have the best power to weight ratio of the power sources I compared. 

Although both are Lithium based, there are some differences between the two:

  • LiPo batteries consist of a set of 3.6V cells (between 3V - discharged and 4.2V - fully charged).
  • LiFePOo4 batteries consist of a set of 3,2V cells (between 2,8V - discharged and 3,6V - fully charged). 
  • LiFePO4 batteries have a higher number of recharge cycles (approx. twice the number of LiPo recharge cycles)
  • LiFePO4 batteries are intended for high power applications. They exhibit a more constant discharge voltage and are considered to offer better safety than other Lithium-based batteries.
  • LiPo batteries are relatively cheaper and lighter (relatively = at the same capacity)

With this list in mind I initially chose to go for LiFePO4 batteries. The biggest I could find were 9.7Ah, capable of delivering 10C (meaning that the peak current is 10x the capacity). With a weight of around 1kg, they fit my requirements well.

After 3 years of working with these batteries I have found that the capacity has deteriorated to the point that it starts to annoy me. I can barely run an activity of 2h on two batteries.
When adding a new battery to my collection, I chose a LiPo this time. The main reason to choose this battery over a new LiFePO4 is that I found them in larger capacity (16Ah).

LiPo and LiFePO4 sizing
When you are going to select your battery you need to understand one more thing: a code with #S#P. This tells you the amount of cells the battery has in series and in parallel. The amount of cells in parallel is not that interesting, as it is the given design for the capacity you are buying (and that number is clearly defined in mAh). The amount of cells in series is more interesting as it tells you what voltage range the battery will operate in. There is of course not one voltage for a battery. It varies along its discharge curve. The good news is that the discharge curve is rather flat.


Discharge curve for a LiFePO4 battery (@ different currents)

Discharge curve for a LiPo battery (@ different currents)
Your radio is most probably happy to take 12-14V. With a LiFePo4 you should therefore go for a 4S version. The voltage of this battery varies between 14,4V (full) and 11,2V (discharged) - most of the time around 12,8V.

If you decide to go for a LiPo battery, then you can either go for 3S (voltage between 9-12,6V) or 4S (voltage between 12-16,8V). Looking at the discharge curve, you will find that with a 3S battery you will quickly drop to a voltage where your radio might not operate anymore or with less output. I used this with my FT-817 and it is a workable solution. At a higher current draw with my FT-857 I found that the battery was unusable too soon. I therefore decided to go for a 4S version. 

LiPo voltage conversion
If you have chosen a LiFePO4, you are ready to go out and activate whatever place you want to. If you went for the LiPo S4 you have one more challenge to go: your set probably won't like the 16.8V of your fully charged battery. So how do you bring this voltage to an acceptable range?

I chose a buck (step down) converter to do the job. You can find them on ebay rather cheaply (imo) as complete modules with adjustable output voltage. I only added a few capacitors and now have a steady 13V LiPo battery with 16Ah capacity.


DC-DC voltage step down conversion

LiPo and LiFePO4 connectors
One other thing to look at are the connectors of the battery. They come in different shapes. Most commonly used are the XT60 and the bullet connectors. The latter are used on higher capacity batteries.
I decided to standardise on one type of connectors - in my case the bullet connectors (as you can see from the buck convertor). So I have made conversion cables to go from different types of connectors (XT60, banana plugs, car cigarette lighter) to bullet connectors.

That is about it regarding power sources for portable operation. In a future post I will zoom in on working with an amplifier while working portable.